BLOG

What Causes a Vacuum Cleaner to Lose Suction?

Does your vacuum suck at sucking? What Causes a Vacuum Cleaner to Lose Suction? Before you throw out your machine and spend plenty of cash on a replacement one, inspect these 5 tips from Domestic CEO to diagnose and effectively fix your sickly vacuum.

we’ve all seen the commercials for vacuums that lose suction. It’s true, a vacuum that doesn’t have suction isn’t a very useful housekeeping tool. the answer presented within the commercials is to shop for a far better, costlier vacuum.

I would argue that it doesn’t take a $500 vacuum to urge your floors clean. In fact, for the past 5 years, I even have been using an equivalent $40 vacuum in my house and it works great. Keeping your vacuum working simply takes a touch knowledge of why a vacuum would lose suction.

If your vacuum sucks (and not during a good way), you’ve come to the proper place. Today, I even have the highest 5 reasons a vacuum loses suction and what you’ll do about it.

See Also: How Often Should You Vacuum Hardwood Floors?

Reasons That Causes a Vacuum to Lose Suction?

Following are the reasons that causes a vacuum cleaner to lose suction.

Reason #1: the peak Is Wrong

The first and most elementary reason a vacuum isn’t picking things up off the ground is that if the peak setting for the vacuum is just too high for the sort of floor you’re vacuuming. there’s usually a touch dial or lever on a vacuum to boost or lower it. it’s going to say “Bare floor,” then have numbers 1 through 5 thereon. A bare floor is that the lowest your vacuum can go and will be used for any tile, wood, or another hard flooring because it’ll seal the vacuum to your floor to permit for the foremost suction power. The lower your carpet, the closer the dial or lever should be to the bare floor setting. If your vacuum isn’t working, first attempt to lower the vacuum to rock bottom setting and see if that fixes the matter.

Reason #2: The Bag Is Full

If the vacuum still isn’t learning on a lower setting, the subsequent thing to see is that if a full dust bag or collection canister is responsible for your vacuum’s loss of suction. Luckily, this is often very easy to work out because of the explanation for your vacuum’s poor performance. there’ll be a fill line on the front of a bagless vacuum, and the dust bag of both upright and canister vacuums. If the dirt and hair are over the fill line of either collection spot, there’s no more room for the things to gather. The vacuum will still sound like it’s working, but won’t have any suction power to select up the things on your floor. most frequently simply emptying the gathering canister or changing the dust bag will solve a vacuum’s suction problems.

If that does not work, it is time to see out the hose. Here’s how…

Reason #3: The Hose Is Clogged

If changing an over-full dust bag or emptying the canister didn’t resolve the difficulty, there may are such a lot of stuff trying to urge into the vacuum that it clogged the hoses resulting in the bag or canister. If you remove the bag or canister and appearance into the opening where they attach to the vacuum, you would possibly see a clog of hair. If you do, grab some tweezers and begin coitus interruptus hair chunks. If it doesn’t appear to be, you’re getting all of it, you’ll detach the hose from the vacuum and work thereon that way too.

If you discover there’s a clog within the middle of the hose where you can’t reach together with your fingers or tweezers, there are 2 ways in which I even have found to get rid of stubborn clogs. the primary is to completely remove the hose, take it outside, tightly hold onto the unclogged end, and spin the hose around as fast as you’ll. The centrifugal motion will force the clog to the top of the hose so you’ll pull it out. the opposite way I’ve discovered to unclog a vacuum hose is to use an extended stick, sort of a broomstick. Carefully start to feed the stick into the vacuum hose. once you get to the clog, begin to push it through until it pops out the top of the hose. With either of those methods, do them outside and have an ashcan ready because there’s usually a poof of loose dust that will release with the clog.

See More: Bissell Pet Hair Eraser Turbo Plus Review

Reason #4: The Vacuum Isn’t Airtight

Just like its name, a vacuum relies on the machine creating a vacuum to suck up dirt from the ground. If air is escaping the system, it can’t pull the things up.

If the vacuum isn’t filled with dirt, and therefore the hoses aren’t clogged, a subsequent common reason that your vacuum isn’t working well might be because it’s not airtight. a bit like its name says a vacuum relies on the machine creating a vacuum to suck up dirt and scraps from the ground. If air is escaping the system, it can’t pull the things into the bag or canister. While this sounds very technical, the foremost common reasons for this happening are no-brainer mistakes that we make.

The first place to see is where the hose connects to the vacuum. If you’ve got pulled the hose bent use the attachments, you’ll not have gotten it back within the hole of the bottom tight enough. If there’s a niche for air to urge round the closure, your vacuum won’t devour much from the ground. make sure the pieces are securely put together. If that appears good, check to form sure your dust bag is securely attached to the vacuum. If you didn’t push it on far enough when installing the dust bag, it’s going to have fallen off and thus there’s no suction being created.

If you continue having problems, you’ll always use a touch adhesive tape on the folds of the bag to make sure it’s sealed airtight.

Reason #5: The Roller Is Clogged

If you’ve checked the bag and hoses, and everything appears to be good, the ultimate step is to flip your vacuum over to see the roller. If the roller is wrapped with hair or yarn from your carpet, it won’t be ready to turn or brush through the carpet and fail miserably at learning dirt. If you are doing find that the roller of your carpet is clogged and furry-looking, this will easily be fixed with a pointy pair of scissors. Starting at one end of the roller, snip through the hair and gunk a touch at a time. The furry mess will come off in small pieces, so as you narrow, start pulling it away and tossing it within the trash. Once you’re done, flip the vacuum over and see if it’s working better.

At now, if your vacuum still isn’t working, you’ll want to think about taking it to a vacuum fix-it shop. Call around to local repair shops to seek out if they service your make and model. Vacuum repairs are often fairly inexpensive, but if you’ve got a bigger problem, it’s going to be more cost-effective to get a replacement vacuum. The person on the opposite end of the phone could also be willing to try to a touch diagnosis over the phone before you lug it right down to the shop. This won’t be incredibly accurate, but counting on your vacuum and what symptoms it’s, they’ll tell you to skip the repairs and buy a replacement one.

Until next time, I’m the Domestic CEO, helping you’re keen on your home.

How to Fix Lost Vacuum Suction

When your vacuum loses suction, it is often costly to exchange the whole machine. Lost or reduced suction isn’t uncommon, and lots of vacuum cleaners suffer from an equivalent issue. Read on to find out the way to fix lost suction in your vacuum instead of pocket money on repairs or a replacement machine.

Step 1 – Diagnose the matter

Vacuum cleaners are all built with an equivalent principle in mind. A motor generates power which powers a vacuum which, in turn, creates suction to lift debris. the foremost common areas of suction loss are within the hose itself, the dust bag, clogged rollers, broken vacuum belt, or a faulty gasket. All of those problems will lead to the vacuum losing suction.

Step 2 – Check the Rollers

Examine the rollers to form sure they’re completely clear. Remove any hair, paper, or large portions of other debris. Once you’ve removed the debris, try vacuuming again. If the matter persists, try the subsequent steps.

Step 3 – Look within the Bag or Canister

Whether or not your vacuum features a bag, a full container can cause loss of suction. confirm that you simply empty the bag and wipe down the within of the canister. once you have the bag or canister removed, you’ll also check where the hose sends the debris into the receptacle. Check for clogs and dirt round the seal, also as any signs of wear and tear or tear. Replace the bag and canister when clean, and operate the vacuum once more. If there’s still no suction, then the matter is elsewhere.

Step 4 – Check for Breaks within the Hose

If the hose of the vacuum is broken or cracked or features a hole, the machine will certainly lose suction. Detecting an opportunity is often difficult. If you’ve got a vacuum that will suck up water, try washing the hose in soapy water, then reversing suction. Bubbles will begin to make at any holes or cracks. Otherwise, you’ll simply wrap the whole house during a layer of either adhesive tape or electrical tape.

Step 5 – Replace the Belt or Gasket

If the rollers are clear, the bag is empty and therefore the hose is sealed, your problem is presumably either the gasket or belt. to repair this, you’ll get to open the vacuum. A belt could simply be jammed, so shop around the mechanism for any debris that would cause that to happen. If the belt is fragile or cracked, then replace it. A gasket could even be wiped out and broken. Simply replace it with a replacement one.

See More: Eureka Nen110a Lightweight Stick Vacuum Cleaner Review

My Vacuum is Leaving Debris Behind!

Well, that’s annoying. this is often a less severe symptom of most of the issues within the previous section. It just means your vacuum is producing some suction, but something’s stopping it from doing its absolute best sucking.

Your bag or canister could be full.

Check your brush. Clean your brush roll and its bearings. If your brush is simply a lumbering cylinder of lint and hair, it’s not getting to do an excellent job.

If it’s not a brush problem, it’s possibly a belt problem. Belts could be broken or too stretched. They also tend to fall far away from time to time. Check the video above and either replace the belt or consult knowledgeable.

My vacuum is Extra Noisy.

Most vacuum cleaners are loud enough to form their presence known. We wish to consider it as a boisterous hello. When your vacuum makes extra noise, though, that sometimes indicates trouble in paradise.

Electric motor for vacuum cleaner Check your hose for obstructions. When an object can’t quite make it through the noise, it can make some weird noises once the suction starts. If this is often your problem, it’s a simple fix.

Check your belts. Again, belt problems are the foremost common problems. When belts aren’t attached or are on their answer, they will exclaim for attention with some truly heinous noises.

If it’s not your hose or belts, your motor is perhaps on the answer. Motors get extra noisy before they provide up permanently. If you think that this is often the case, contact your local vacuum store (that’s us.)

My vacuum Smells Bad

Have you ever used an old vacuum that just stinks up an area once you turn it on? It’s pretty gross, right? nobody wants that.

  • Empty the bag or canister, you silly goose!
  • Check your air and exhaust filters. Clean or replace them.
  • If your vacuum remains to produce an odor after you’ve thoroughly checked your dust bag, filters, and brush roll, take it to knowledgeable.

Hopefully, you’ve found your vacuum problem on this list and you’ve been ready to repair it. Remember, YouTube is usually an honest resource for creating quick and dirty repairs. As a rule, always take care of running motors, belts, and brushes. You don’t want to urge your hair, clothing, or jewelry stuck in them– though we’ve heard of stranger ways of losing wedding rings.

If you can’t easily fix the matter, ask us before you purchase a replacement vacuum. we’d be ready to fix your current appliance, which can keep you right track for that vacation to the Oregon coast.

No Responses

Join The Discussion

This site uses Akismet to reduce spam. Learn how your comment data is processed.

error: Content is protected !!